ESD protecting MOSFETs

Anything not specifically related to NBTV, but at least of some technical nature that might be of interest to NBTV members. Items for sale and links to retailers do not belong here.

Moderators: Steve Anderson, Dave Moll

ESD protecting MOSFETs

Postby smeezekitty » Sun Nov 22, 2020 8:27 pm

I'm putting this in off topic because even though it is NBTV related, it is more of an electronics question.

I am using a pair of Klaas Robert's LED drivers for my bicolor mechanical TV. They work amazingly!
Except I have gone through two MOSFETs now (they're stuck on) due to (I assume) ESD damage. They don't get hot so its the only thing I can think of.

Is there any way to protect the gates of the MOSFET without sacrificing too much NBTV bandwidth?

Thank you
smeezekitty
Evil Genius
 
Posts: 180
Joined: Fri Jan 29, 2010 11:42 am
Location: USA

Re: ESD protecting MOSFETs

Postby Steve Anderson » Mon Nov 23, 2020 3:48 pm

I've seen more than one version of a MOSFET LED driver, maybe not all done by Klaas, but if you could post up the circuit here that may help.

I assume it/they worked for a while and the next time you powered up they're dead, correct? Grounding and the power supply would be my first thoughts. Did you do anything else than power-down then power-up again? i.e. plug/unplug, solder/unsolder anything?...basically any changes aside from power-off and power-on? Is the power supply switched-mode or linear? Also anything 'dirty' sharing the same power supply? e.g. a brushed DC motor?

I'm sure Klaas will have his thoughts as well...

Steve A.
User avatar
Steve Anderson
"Fester! Don't do that to 'Thing'"
 
Posts: 4256
Joined: Fri Mar 30, 2007 10:54 pm
Location: Bangkok, Thailand

Re: ESD protecting MOSFETs

Postby smeezekitty » Tue Nov 24, 2020 12:49 pm

Maybe it wasn't actually Klaas who designed the circuit. But in any case, that's where I got it from. viewtopic.php?f=1&t=2557#p23409

I had touched the input lead at one point so that's why I suspect ESD. The power supply is an HP adjustable linear supply (fairly high quality).
smeezekitty
Evil Genius
 
Posts: 180
Joined: Fri Jan 29, 2010 11:42 am
Location: USA

Re: ESD protecting MOSFETs

Postby Steve Anderson » Tue Nov 24, 2020 6:02 pm

smeezekitty wrote:I had touched the input lead at one point so that's why I suspect ESD.

Most discrete MOSFET devices are fairly well protected from ESD these days but it still is wise to take precautions. That also applies to CMOS and all other varieties of static-sensitive devices.

I know I bang on about this seemingly endlessly, but supply decoupling/bypassing is essential. Even if you've only got 30cm (12") of wire from the PSU to the application, add the supply caps. Even without zapping chips or discretes through handling, they're still at the mercy of cool and low-humidity conditions. that's Europe and the US at this time of year. Thunderstorms...another subject. (I'm in the tropics).

The gates to static-sensitive devices can be protected externally depending on the application. But as you assemble the final circuit you need to be careful.

It might be worth investing in an wrist-earthing/grounding strap, I haven't, but maybe where you are it's a good insurance policy. Make sure your soldering iron is properly earthed/grounded as well...in this case mine is...

https://www.amazon.com/earthing-bracele ... g+bracelet

Many, many others out there too...

Steve A.
User avatar
Steve Anderson
"Fester! Don't do that to 'Thing'"
 
Posts: 4256
Joined: Fri Mar 30, 2007 10:54 pm
Location: Bangkok, Thailand


Return to Off Topic

Who is online

Users browsing this forum: No registered users and 3 guests